Why The Refrigerator Is Not Cooling? 3 Superb Reasons About It

Why the refrigerator is not cooling? The refrigerator is a great appliance for storing food, but it can be a slight nuisance when it doesn’t work properly. You might be asking, “How can I fix this?”

So, do you want to know the reasons why the refrigerator is not cooling? Read this article until end to know more about it. In this blog, we also have an article about frigidaire luxury refrigerator that you might want to read about it.

Why The Refrigerator Is Not Cooling

Warming up the refrigerator isn’t always an apparent solution. There are many possibilities for what is causing the problem. Malfunctioning components may be difficult to identify, particularly when determining which portion is causing the issue: 

Compressor for a refrigerator

The compressor is the component of the refrigerator that compresses and pushes refrigerant vapor into the coils located outside of the refrigerator. The pushing and pressure generates heat, resulting in the formation of hot gas, which eventually cools and absorbs heat from the freezer and fridge.

If your freezer fan is still operating but your fridge isn’t getting cold, it’s possible that your compressor or compressor start relay is broken.

The compressor is placed behind and at the bottom of your refrigerator. It’s a tank-like black section. The compressor start relay is the component that feeds the compressor’s cables. To reach both pieces, you’ll need to lift your fridge away from the wall. Before you begin, disconnect your refrigerator from its power source.

The Solution: Replacing the compressor start relay is far simpler and less expensive than replacing the compressor itself. Simply purchasing a new relay and testing it with your present compressor can reveal if you need a new compressor or whether your current problem has been resolved.

To replace the compressor, you must first properly separate it from the suction and discharge lines. Before you can release the bolts that keep the compressor in place, you’ll need to remove the electrical package and cut the high and low wires. You may relocate the component closer to the access point and disconnect the ground line. Your new compressor must be attached to your suction, discharge, and process lines. Welds will be required to secure the lines in place. Before evacuating the new system and dumping the new charge, be careful to move the rubber grommets from the old compressor to the new and to turn over the crossover line.

Condenser Coils

Condenser coils transport hot gas from the compressor to the evaporator coils. The refrigerant cools and returns to liquid as it flows through the coils under high pressure. Clogged condenser coils may cause poor air circulation, limiting your refrigerator’s capacity to maintain cold.

Condenser coils are situated across the bottom of the refrigerator or on the rear. They run from the compressor to the freezer.

The Solution: If your coils are blocked, they may need cleaning. Before removing the toe grill, turn off the refrigerator (check your owner’s handbook to determine whether your toe grill may be taken directly off without any further procedures). Push a coil brush into the condenser coils to remove any dust that has accumulated there. The dust may then be vacuumed off and the toe grill reinstalled.

Fan Condenser

The condenser fan circulates cold air through the compressor and condenser coils as they function. When the compressor is functioning, the fan should also be running. If the condenser fan fails to perform correctly, the temperature of the refrigerator might increase and the compressor can overheat.

The condenser fan is situated in the bottom cabinet between the compressor and condenser coils. It’s worth noting that refrigerators with condenser coils on the rear won’t have a fan.

The Solution: First, make sure the condenser fan is spinning freely and isn’t being hindered by anything. It is conceivable that dust or other items are preventing the blades from rotating properly.

If nothing is preventing the blades from spinning, the condenser fan motor may need to be replaced. A replacement fan motor may be purchased from a local appliance parts dealer or from the maker of the refrigerator. Simply unfasten the mounting screws that keep the fan in place and gently remove that component from the motor compartment to replace the motor. Remove the mounting bracket that secures the old motor to the blades and replace it with the new motor.

Our Latest Post:

💻 Wine Cooler | Waffle Makers  |  Single Wall Oven

---