How to install an electric range? Whether you are a home chef or a professional, cooking on a stove can be a lot of work and a hassle. Fortunately, there is a way to make cooking easier and more convenient.
Electric ranges are a perfect choice for those who want the convenience of an oven without the hassle of a gas range. The installation process for an electric range is not difficult and can be done by a professional or a do-it-yourselfer.
If you are searching a way about how to install an electric range, you have come into the right place! In this blog, we also have an article about best double oven electric ranges on amazon that you might want to read about it.
How To Install An Electric Range
In the days when a freestanding range was the only option for replacing an old electric range, you now have a much broader selection of options to choose from. Freestanding, slide-in, and drop-in options are all current and fashionable. There are a few variations between these electric range kinds that you should be aware of if you intend to install them yourself.
The opening must be prepared for the installation
To illustrate how each range style requires different openings, check out these sketches.. The manufacturer’s instructions for unpacking, assembling, and installing a new range should be reviewed before installing or altering existing cabinets and countertops. Make sure that your range’s width and depth are accurate by taking measurements of the appliance itself.
Adjustable feet on freestanding and slide-in ranges make it simple to position and level the cooktop with the surface. Anti-tilt safety brackets are included with most slide-in and drop-in ranges so that they can be securely fastened. Check your installation instructions carefully, and make sure there’s a firm spot inside your opening where the brackets may be fastened to the cabinetry, wall, or floor.
The range’s electrical needs.
There must be a dedicated 40 or 50 amp 240V circuit for all electric ranges, and it must terminate in a junction box within 4 feet of the range’s intended location. Wiring is already in place if you’re replacing an electric range that’s currently in your home. A professional electrician can make the necessary modifications to the wiring in accordance with local codes if you’re unsure or installing a new range in a new location.
A 240-volt receptacle or an approved junction box can be used to connect an electric range to a dedicated circuit. Consider hiring an electrician if you’re going with a direct-wired range. Nonetheless, if there is an existing 240-volt receptacle, it is safe and simple to plug in the range.
You’ll need to connect a power connection to your range
Kits of 3- and 4-wire 240-volt appliance power cords are available. All 240-volt circuits have two hot conductors (often red and black) and one neutral wire (typically white) (usually color-coded white). A green ground wire is also present in 4-wire cables.
With 3-wire connections, the neutral wire is grounded via a piece of copper known as a ground link; with 4-wire connections, the neutral wire is grounded by an entirely separate wire. Appliance hookups to new circuits since 1996 have required a separate ground, but if you’re connecting a new range to an existing three-wire circuit, the National Electric Code (NEC) allows you to use 3-wire cable and ground the appliance to neutral.
The receptacle that is currently in use should be compared to the ones depicted below to ensure that you are using the correct one if you intend to connect the range’s power cord yourself.
Start by finding the terminal block, which is normally located at the back of the range, near the bottom. To get to the terminals, you might have to remove a cover plate. Large round holes can be found on a plate located just below the exposed terminals:
- Use some screws to partially tighten a strain-relief clamp into place.
- Allow the terminals of the power cord to extend through the strain-relief clamp long enough to reach the terminal block’s connection bolts.
- Remove the nuts from the terminal bolts with a nut-driver.
- With a 3-wire cable, connect the black wire to the left terminal, the red wire to the right terminal, and the white wire to the middle terminal. The ground link, which is held in place by a green screw, should be touching the center terminal. Tighten the nuts back on the terminal bolts by sliding the wires all the way back.
- To cut or remove the terminal link from a 4-wire cable, release the green screw on the terminal block. Red and black wires connect to the terminal bolts at left and right, while green wire is fastened to a screw beneath the green screw.
- Tighten the clamp’s screws all the way.
- Plug the power cord into the receptacle after turning off the range circuit at the main service panel. Afterwards, switch the power back on at the panel.
- Make that the burners, lights, and timers on the range are all operational.
Slide the new range into place and make sure the cooktop is level after the electrical connection has been completed and checked. You may need to modify the legs or do some shimming to get it to fit. Once you’re satisfied with the position and fit, follow the manufacturer’s instructions to secure any anti-tip brackets you installed. For a fresh start in the kitchen, you must remove all of the packaging materials first.
Our Latest Post:
💻 Wine Cooler | Waffle Makers | Single Wall Oven
Was this helpful?
Hi there! I’m a food enthusiast and journalist, and I have a real passion for food that goes beyond the kitchen. I love my dream job and I’m lucky enough to be able to share my knowledge with readers of several large media outlets. My specialty is writing engaging food-related content, and I take pride in being able to connect with my audience. I’m known for my creativity in the kitchen, and I’m confident that I can be the perfect guide for anyone looking to take their culinary journey to the next level.
