Range hood under cabinet
An under cabinet range hood can be found beneath a kitchen cabinet, as the name suggests. So, How to install a range hood under cabinet? In this article you will know how to do it.
The primary purpose of this type of range hood is to ventilate your kitchen by expelling smoke, steam, heat, and unpleasant smells that result from frequent cooking or food preparation. In this blog, we also have best under cabinet range hoods on amazon that you might want too see.
Benefits of Range Hood Under Cabinet
There are several benefits to installing an under-cabinet range hood over other types of kitchen ventilation systems:
- Under-cabinet range hoods allow you to maintain cleanliness in your home, as they keep grease and odors out of sight. This helps prevent unwanted bacteria growth, which could lead to health problems for you and your family.
- An under-cabinet range hood can be easier to install than some other types of kitchen ventilation systems because there’s less work involved. You may have to remove an existing air duct and then replace it with one meant for a new range hood installation.
- Under-cabinet range hoods don’t require any special wiring, making them more affordable. They also don’t need any specialized electrical connections, so if you own an older house, you won’t have to worry about adding unnecessary wires.
- An under-cabinet range hood offers plenty of space to store pots and pans, allowing you to cook without worrying about dropping items on the floor.
How to Install a Range Hood Under Cabinet?
Measure Your Kitchen Cabinets
Take a measuring tape and measure the width of your cabinets. If you want to install a range hood right above your countertop, make sure that the distance between the top edge of the range hood and the bottom edge of the countertop is at least 7 inches. If not, consider placing the range hood under the counters instead. For example, if the kitchen has two upper cabinets, place the range hood between the middle ones.
Remove Existing Duct Work
Once you know where you want to install a range hood and how much room you have available, it’s time to start removing the old ductwork around the area of the kitchen. Start by turning off the power supply to the entire house. Then, disconnect all fuses that might be located near the wall outlet. It’s important to note that when working on power lines, be careful not to touch any live wires.Once you’ve removed the existing ductwork, turn off the gas supply line leading into the kitchen. Disconnect the gas valve, too. Next, check for water leaks. A leaky pipe will usually show up as damp spots on the walls or floors.
If you find anything like this, repair it immediately before moving forward with your range hood installation project. In most cases, a leak isn’t harmful unless water gets behind drywall or plaster. To avoid damage to your property, call a professional plumber to fix these issues.
Cut Out Holes for Installation
Now that you’re ready to get started to install a range hood, use a utility knife to cut a series of holes along the length of the wall. Make sure that these holes are spaced apart by at least 6 inches. Remember to leave enough clearance around each hole to accommodate the pipes and cables that run through it.
Use a hammer and nails to secure the first piece of wood to the wall. Once you’ve finished fastening the pieces together, use a drill to create another set of holes, approximately 6 inches away from the first set. Repeat this process until you reach a spot that matches the height you’d like your range hood to sit.
Drill Holes for Drain Line Pipes
Now that you’ve created the appropriate number of holes for your range hood drainage system, insert drain pipe fittings into them. Use a wrench to tighten the pipes securely. Afterward, take the fitting off the fixture and attach it to the wall using screws.
Attach brackets to the outside of the range hood and then screw the bracket firmly onto the wall.
Connect the Piping System
The final step involves connecting the piping system to your range hood. Attach the flexible hose to the range hood exhaust port. Then, connect the other end of the hose to your ventilator. This should ensure that there’s no blockage in the exhaust flow. Turn on the fan of the range hood, adjust its settings according to your preference, and enjoy your new ventilation system.
Our Latest Post:
💻How To Use a Churro Maker | Clove Grinder | How to Incubate Yogurt
Was this helpful?
Hi there! I’m a food enthusiast and journalist, and I have a real passion for food that goes beyond the kitchen. I love my dream job and I’m lucky enough to be able to share my knowledge with readers of several large media outlets. My specialty is writing engaging food-related content, and I take pride in being able to connect with my audience. I’m known for my creativity in the kitchen, and I’m confident that I can be the perfect guide for anyone looking to take their culinary journey to the next level.
